DIN Rail Industrial PLC Ethernet Bridge is a powerline telecommunication product which being developed by WonderTek Technology (KunShan) Co.,LTD., it supports the G.hn protocol and the actual bandwidth up to 450Mbps. The product has been widely used in many aspect just as railway, mines, industrial Telecommunication and metro etc...
1.1.1 Technical parameters
Support G.hn;
Industrial DIN rail style installation;
Actual bandwidth up to 450Mbps;
The maximum transfer distance up to 800 meters;
Self-adapt the rate;
Compatible with all G.hn devices;
One Domain Master can manage 7pcs End Point;
There can be 7 groups(7 different Domain Master) of PLC telecommunication devices in the same power line circuit;
1.1.2 Manageability
Support Remote Firmware update(TR069);
802.3D Ethernet Bridge;
802.1Q VLAN;
Quality of Service(QoS) ;
IGMO(IPv4)Snooping&MLD(IPv6)Snooping;
Support local web management;
1.1.3Operating environment
Working temperature: -40℃-80℃;
Operating humidity: 10%-85% no condense;
Storage humidity: 5%-90% no condense;
|
Interface |
1*LAN 10/100/1000Base-TX self adaption RJ45， |
||
|
LED display light |
Ethernet, PLC link ,power |
||
|
Transfer band |
100MHz (based on G.9963) 50Mhz MIMO |
||
|
Protocol（PHY） |
IEEE802.3，IEEE802.3x, IEEE802.3u G.hn |
||
|
Security |
128-AES |
||
|
Bus unit per segment |
Up to 7 |
||
|
Installation |
Rail TS35 |
||
|
Protection type |
IP40 |
||
|
Transfer rate（PHY） |
800Mbps |
||
|
Modulation |
OFDM |
||
|
Effective transfer rate |
TCP/IP 450Mbps |
||
|
Manageability |
Remote Firmware update，support TR-069（optional） |
||
|
802.1D Ethernet Bridge |
|||
|
802.1Q VLAN |
|||
|
Quality of Service(QoS) |
|||
|
IGMO(IPv4)Snooping&MLD(IPv6)Snooping |
|||
|
Operating temperature |
-40℃-80℃ |
||
|
Size |
120*90*45 (mm)（L×W×H） |
||
|
Weight |
0.65kg |
||
|
Operating environment |
Operating humidity:10%-85% (no condense) |
||
|
Storage humidity: 5%-90%(no condense) |
|||
|
Certification |
FCC、CE class B, RoHS |
||
(1) Packet loss：≤0.1%（100M,load 70%）.
(2) Support 7*24 hours all weather operation.
(3) Hardware watch dog function.
(4) PING≤2MS, Up to 16 pcs in each group.
The testing voltage which the device should be beared: ±6kV direct Discharge, ±8kV air discharge;
Discharge number in Each sensitive testing point: Plus-n-Minus 10 times each;
Every time the discharge interval is 1 s, according to B/T 17626.2-2006.
The testing voltage which the device should be beared:
between the power supply voltage port and ground: ±2.0kV;
between signal circuit and ground: ±1.0kV;
repetition frequency: 5KHz,
test duration: 1 min/ time;
testing times: Plus-n-Minus 5 times each. According to GB/T 17626.4-2008.
The testing voltage which the device should be beared: ±2kV;
The interval of continuous impulses: 1min/time;
Test number: Plus-n-Minus 5 times each.
According to GB/T 17626.5-2008.(protection: all models protection and varistor series of discharge tube type)
Meet the demand of MX3 in TB1433(0-200Hz,2g acceleration, maximum amplitude 7mm), interface with no loose, device with no Sealing off and drop in the test.
------------------------------------------------------------------------------------------------------------------------------------------------------
AC 3 phases+1 N(4-wire link to the device connected to the input end of the network, and L+N link to the terminal network device)
------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------
AC 3phases +1N(each device needs four wires)
------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------
AC 3Phases
--------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------
AC:
------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------
DC:
------------------------------------------------------------------------------------------------------------------------------------------------------
|
Model |
Ethernet Port |
Line Environment |
Network Structure |
|
WD-1001M-DIN-SG-T |
1 |
AC(3 phases+N) |
Network access points must be connected in 3 phases, and terminals can be mixed in 3 phases and 1 phase （85-520V） |
|
WD-1001M-DIN-SG-T4 |
1 |
AC(3 phases+N) |
Network access points and terminals require uniform standard connections （85-520V） |
|
WD-1001M-DIN-SG-V3 |
1 |
AC(3 phases) |
Only three phase connection, and according to the unified standard wiring （85-520V） |
|
WD-1001M-DIN-SG-A |
1 |
AC(phase + null + ground) |
Single phase with or without ground （85-520V） |
|
WD-1001M-DIN-SG-D01 |
1 |
DC |
9-36V |
|
WD-1001M-DIN-SG-D02 |
1 |
DC |
18-72V |
|
WD-1001M-DIN-G-T |
1 |
AC(3 phases+N) |
Network access points must be connected in 3 phases, and terminals can be mixed in 3 phases and 1 phase （85-520V） |
|
WD-1001M-DIN-G-T4 |
1 |
AC(3 phases+N) |
Network access points and terminals require uniform standard connections （85-520V） |
|
WD-1001M-DIN-G-V3 |
1 |
AC(3 phases) |
Only three phase connection, and according to the unified standard wiring （85-520V） |
|
WD-1001M-DIN-G-A |
1 |
AC(phase + null + ground) |
Single phase with or without ground （85-520V） |
|
WD-1001M-DIN(D) |
1 |
DC |
10-80V |
Learn more
